What we install
Installation covers anything that connects to water supply or drains. That includes kitchen and bathroom sinks, toilets, bathtubs and showers, laundry boxes, dishwasher and ice maker lines, outdoor hose bibs and utility sinks. It also covers new water lines and drains for additions, garages and converted rooms.
Gas piping for ranges and dryers is not part of what this page offers, so ask the dispatcher if you need it. Water heaters have their own pages under water heater installation, because venting, sizing and safety valves need a closer look.
Fixtures by room
Each room has its own checklist. The plumber walks the space with you, confirms what is there and identifies what must change.
Kitchens
A kitchen sink needs hot and cold supply stops, a trap and a drain connection that slopes toward the wall. Dishwashers need a supply line and a drain connection, usually through an air gap or a high loop. A pot filler or an instant hot tap adds its own lines and sometimes an electrical need.
Bathrooms
Vanities, toilets, tubs and showers all need correct rough-in dimensions. A toilet's drain must sit the right distance from the wall, and a shower valve must be placed at the right height before tile goes up. Changing a layout means moving the drain, which is far more work than replacing a fixture in place.
Laundry and utility
Washers need a recessed box with two valves and a drain standpipe that reaches the right height. A laundry sink in a garage needs a trap and a vent. Outdoor taps need a vacuum breaker to protect the home's water from backflow.
Remodel on the calendar? Call and talk through the plumbing before the walls open.
Call (855) 575-2890Which fixtures need what
| Fixture | What the plumbing needs | Common complication |
|---|---|---|
| Kitchen sink | Hot and cold stops, trap, drain connection | Cabinet depth and drain location |
| Dishwasher | Supply line, drain hose, air gap or high loop | Tight space, hose routing |
| Toilet | Cold supply stop, drain flange set at the correct height | Flange condition, rough-in distance |
| Bathtub or shower | Valve, mixing control, drain with a trap | Access panel, subfloor strength |
| Washing machine | Recessed box with two valves, drain standpipe | Standpipe height and trap |
| Hose bib | Cold line, vacuum breaker | Wall penetration and exterior finish |
General descriptions, not quotes. The scope is set after the plumber sees the space.
Remodel rough-in: the stage that matters most
Rough-in is the plumbing placed inside open walls and floors before finish work. It is the stage that cannot be fixed cheaply later, because tile, drywall and cabinets hide it. A drain set an inch off, a valve at the wrong depth or a missing vent can mean opening finished walls.
Plan the plumbing before choosing fixtures, not after. Fixtures such as freestanding tubs, wall-hung toilets and double-vanity sinks need specific rough-in dimensions, and the manufacturer's sheet shows them. Send us those sheets before you buy, and the plumber can confirm the plan will work.
Why venting matters
Every drain needs air behind the water, or it gurgles and siphons the trap dry. The vent pipe provides that air, and the sizes and runs are set by the Florida Building Code, Plumbing. UPC and IPC are model codes that other states adopt, and Florida has its own. We follow the Florida code and do not guess at a requirement.
Permits and inspections
New plumbing, relocated drains and many remodels need permits, but the rules vary. Permit rules vary, so ask the City of Tavares Building Division at 201 E. Main Street before you start. The division handles permits for city projects, and calling first can avoid a stop-work notice later.
Other cities post different requirements. The City of Leesburg, for example, lists a plumbing layout or diagram among the items for a residential plumbing permit. So have a simple sketch of your fixtures ready, whichever town you are in.
How an installation job runs
- 01Walk the space
The plumber looks at the room, the existing lines and where the water shutoffs are.
- 02Confirm the plan
Fixture sheets, rough-in dimensions and the route for supply and drain are agreed, and the price is explained.
- 03Rough-in or set
New lines go in, or fixtures are set and connected, depending on the stage of the project.
- 04Test and show you
Water is turned on, every connection is checked for leaks and drainage, and you see it work.
Hooking up a new water heater or appliance
Appliances often need more than a hose. A water heater needs a shutoff valve, a pressure relief valve discharge line, a drain pan in some locations and, in many cases, an expansion tank. A washing machine needs both hot and cold lines, and an ice maker needs a small dedicated supply.
If your project includes a new tank or tankless unit, tankless water heater sizing and venting are worth discussing early, since they can affect where walls and gas lines go.
Before you buy fixtures
Check three things on any fixture before it leaves the store: the rough-in measurements, the type of supply connection, and whether it comes with a drain assembly. Cheap fixtures often leave out the pieces that matter, and a plumber's trip to buy parts adds to the bill.
Keep boxes, spec sheets and receipts until the work is done and tested.
What plumbing installation costs
Installation prices swing widely, from a single faucet to a full bathroom rough-in. These five factors explain most of the difference.
A one-fixture swap and a new bathroom are not comparable. The number of fixtures and lines decides the labor.
Open framing is quick, and finished walls, tile or slab work take longer and need patching.
A new sink near the old one is simple. A new fixture across the house needs long runs of pipe and a drain slope.
Standard fixtures and PEX are less costly than designer fixtures and copper.
Where permits are required, they add time and cost to the schedule.
Installation is usually planned work, so insurance rarely pays for it. If the work follows a covered loss such as a burst pipe, send your adjuster the plumber's written scope before the work begins.
The fastest way to a real number is a call, because the price is explained before any work begins.
Installation across Tavares and nearby towns
Tavares has downtown buildings along East Main Street, homes on both lakes, and office space in the Lakeview area near Salk Dr, close to the hospital. Each type of building needs a different approach. A small shop converting a space needs a new restroom group and floor drains, while a home on a high water table needs care around slab work.
Slab-on-grade homes are common in Tavares, so plumbing for an addition often means cutting concrete or running overhead. We also serve Leesburg and Eustis, where older buildings may need old lines tied into new ones. If a project includes a repair of failing supply pipe, see our repiping page, and for business spaces our commercial plumbing page.
Frequently asked questions
Permit rules vary by town and by the kind of work. Ask the City of Tavares Building Division at 201 E. Main Street before you start. Replacing a fixture in the same place is often treated differently from moving a drain.
In most cases yes. Send the model number and spec sheet first, so the plumber can confirm the rough-in and parts. Fixtures missing drain or supply pieces may need extra parts, which we discuss before work.
Rough-in is the pipe placed inside walls and floors before finishes. Once tile and drywall go up, changes are costly. Confirm your fixtures' dimensions before the rough-in is done.
This page covers water supply and drain work. Gas piping is a different scope, so ask the dispatcher when you call and we will say whether it is something we can take on.
Usually yes, though moving a drain costs far more than swapping a fixture. The plumber checks slope, venting and slab access before agreeing to a layout, and explains the trade-offs.
Use the Verify a License tool at MyFloridaLicense.com, run by the Department of Business and Professional Regulation. Search by name or license number before agreeing to any work.
Only if the problem is in the lines being replaced. Weak pressure can come from the regulator, the service line or a partly closed valve, and the plumber checks those before suggesting new pipe.
A fixture set right the first time stays dry. Call to schedule the install.
Call (855) 575-2890Sources and standards
Where this page cites a local fact, it comes from a public City of Tavares page, another city's own web page or a published water quality report. Where a figure is not published, the page says so instead of guessing.
Plumbing work in Florida is governed by the Florida Building Code, Plumbing, which is the standard inspectors apply, and permit rules vary by city. The contact page explains how to reach us, and any plumber's license can be checked with the Verify a License tool at MyFloridaLicense.com.